How to Power Fpv Camera? 3 Easy Steps You Can Follow

By clicking on the product links in this article, Rcraces may receive a commission fee to support our work. See our Terms.

An RC user would definitely consider getting an Fpv camera for his RC vehicle. As a result, the users get to a store around and get one for theirs. However, one thing the users often forget is to know about how to power it. That’s when the problem arises.

So, how to power the Fpv camera?

To power up your Fpv camera, you first need to inspect the power input capacity. Once you do that then you must be assessing the video of the camera. Finally, you have to connect the camera to the power. Along with that, you would also connect the transmitter to the power too.

This brief has come up with an outline of what you would be going through. So, reading along you get every detail to know about this.

Get started now!

How Do I Power The Fpv Camera?

You know cameras for RC, whether it is a vehicle or planes, are great. An Fpv camera with your RC can be a great help. But you need to keep on maintaining this too.

So, what the RC users often forget is to get knowledge about powering this. That is when they start suffering with these Fpv cameras. 

So, how to power the Fpv camera? Well, today, we got here 3 simple steps on how to power the Fpv camera. Here you go.

Step 1: Inspect The Power Input Capacity

The first thing you inspect is the input capacity of the power. Remember that any general power cable would work with the video transmitter.

These Fpv video transmitters usually work with any type of regular cable actually. Even if you fail to do so, you can bind the receiver to the transmitter.

They typically work flawlessly on all the regular batteries we use. But you need to make sure the range is alright. That is, it must be ranging from a 2 cell to a 6 cell. 

These transmitters are quite great because they can handle a large variety of voltage. Also, remember that handling the voltage properly is quite important too.

Thus, you are free to utilize any power source that works with your camera and transmitter. It makes no difference if the camera needs a 6 cell or a 2 cell. 

One power supply can be used for two components. However, if your camera needs a stronger power source, that can be a little difficult. 

Most certainly, the transmitter won’t be able to accept as much as a 6 cell, unless it is capable of doing so. 

You’ll need to utilize a separate power supply if it doesn’t, though. One is for the transmitter and another is for the camera.

Thinking of getting a cell for your Fpv camera? Well, here are the ones that we recommend to you.

Product 1 
Product 2 

Hope this helps!

Remember that you need a battery along with the camera. So, get it when you are buying the camera. A lot of users seem to be forgetting about the complementary.

And if you can then get a pair of batteries. Because this would help you to back up the batteries. 

But do not buy over 2 or 3 batteries for the backup. Because storing or keeping the batteries idle for a long time would damage them. So, you better not do that.

Step 2: Assessing The Video

Now, you would see 4 or 5 cables attached to each node with the transmitter. The cables would be white, green, red and black.

The white and green ones are for the audio. These would come in use only if your camera has a mic. Almost every RC cameras have a mic with it. 

Then you would see the red and black ones. These wires include the JST plugs. Although you may not need these now, you will need them later.

These red and black ones are to be used while powering the transmitter. Finally, you would come up with the yellow wire. This is the one that you need the most.

You take this wire and get it into the lower part of the servo connector. Do not use any random or low-quality servo for this. 

Now, you would have to work with the wires of the camera. You would see 3 wires that are red, black, and yellow.

This time take the yellow wire of the camera and plug it into the servo connector. It has to be connected to the upper part of the servo.

Now, plug the wires back into the transmitter as they were. That is how the video setup of the Fpv camera is done.

Step 3: Connect to Power

This time, you have to connect the camera to power. Along with that, the transmitter has to be connected too. 

You have the camera’s red and black wire. These two are coupled in a JST plug at the terminal. These plugs require a 12-volt supply. 

The two JST connectors you have now require 12 volts. This is precisely the reason you require a battery with twin JST plugs. 

What you need to do now is join the battery’s JST connectors to another two. After that, you need to use a 12-volt battery to operate the transmitters. 

You can even power up the camera with it as well. Then the FPV camera is successfully powered. 

You’ve also had experience utilizing the very same power cell to run your camera and transmitter.

So, that is how you can power your Fpv camera yourself very easily. Remember that it is recommended not to overdo any steps provided here.

You may initially seem to go alright. But you would come up with issues with time. So, you better not take any risk of not following the steps properly.

Remember that you need batteries for your Fpv camera. For that, you can use any batteries that are compatible with the camera.

But you still need to make sure that you got a battery of good quality. Do not forget that Lipo batteries are one of them you may consider. 

Because their performance is as good as their maintenance. Remember that it is very simple and easy to charge a Lipo battery. 

In fact, you can get a Lipo battery charged without a charger too. So, you better get along with these batteries not having a pair of batteries already.

FAQs

Can I get an Fpv camera with my RC truck too?

Yes, you can get an Fpv camera with your RC truck too. In fact, this is something that a lot of RC truck users do often. You know there are a number of advantages of using an Fpv camera with RC trucks. This helps you to have a real-time view close to the driving view.

Is there anything that can disrupt the signal of the Fpv cameras?

Yes, there are a few things that can interrupt or disrupt the signal of Fpv cameras. You can not actually control that disruption in any way. A few common disruptions would be wifi connections and even phone calls. So, if you want a disrupt-free connection then you may go somewhere without these.

How much an Fpv camera with 5.8 GHz can go?

With a 5.8 GHz of Fpv camera, you can go around 500 meters. This is an average measurement with the camera. But if you have got any disruptions in between, then the range could be decreased. So, if you want to cover a range of about 500 meters, you better go outdoor.

The Final Words

Now you know how to power the Fpv camera! At this moment, you must have no more confusion left about it.

However, do not forget one thing about it. If you plan to store your Fpv camera somewhere, then you can do it. But do not forget to keep it somewhere clothy or soft. Or else, it might be damaged anytime.

All the best!

About the author

Travis Murray

I am Travis Murray, and my love for RC began in 2017. It gradually turned into a passion, leading me to become an RC enthusiast and blogger. I write in-depth reviews and DIY guides for RC enthusiasts to provide troubleshooting tips and insider knowledge to help starters find the hidden gems in the hobby.
Related Topics

Leave a Comment